AVR320 harman/kardon
Main Remote Control Functions
u Tuning Up/Down: When the tuner is inprocessing and place the unit in a traditional38Speaker Select:Press this button
use, these buttons will tune up or down throughtwo-channel Stereo mode. The first press to begin the process of configuring the
the selected frequency band. If the Tuner Modeselects 5-Channel Stereo, the next press selectsAVR 320Os bass management system for use
Button s^ has been pressed so that the8-Channel Stereo, and the third press selectswith the type of speakers used in your system.
AUTO Indicator X is illuminated, pressing andOSURROUND OFF,� which is true Stereo.Once the button has been pressed, use the
holding either of the buttons for three seconds?/¤Buttonsnto select the channel you
will cause the tuner to seek the next station with30Macro Buttons:Press these buttons wish to set up. Press the Set Button p and
acceptable signal strength for quality reception.to store or recall a OMacro�, which is a then select another channel to configure.
When the AUTO Indicator X is NOT illumi-preprogrammed sequence of commands When all adjustments have been completed,
nated, pressing these buttons will tune stationsstored in the remote. (See page 38 for morepress the Set Button p twice to exit the
in single-step increments. (See page 31 for moreinformation on storing and recalling macros.)settings and return to normal operation. (See
information.)page 22 for more information.)
31DTS Neo:6 Mode Select:Pressing
v OSD Button: Press this button to activatethis button cycles the AVR through the various39Multiroom:Press this button to activate
the On-Screen Display (OSD) system used to setDTS Neo:6 modes, which extract a five-channelthe multiroom system or to begin the process of
up or adjust the AVR 320Os parameters.surround field from two-channel program changing the input or volume level for the sec-
material. The first press selects the lastond zone. (See page 36 for more information on
w Dolby Mode Selector: This button is
DTS Neo:6 surround mode that was in use,the Multiroom system.)
used to select from among the available Dolbyand each subsequent press selects one of the
Surround processing modes. Each press of this
button will select one of the Dolby Pro Logic IIother DTS Neo:6 modes.40Volume Up/Down:Press these buttons
to raise or lower the system volume.
modes or Dolby 3 Stereo. When a Dolby Digital
encoded source is in use, the Dolby Digital mode32Disc Skip Button:This button has no
direct function for the AVR 320 but is most41SPLIndicator Select:This button acti-
may also be selected. (See page 26 for the avail-
able Dolby surround mode options.)often used to change to the next disc in a CDvates the AVR 320Os EzSet function to quickly
or DVD player when the remote is programmedand accurately calibrate the AVR 320Os output
for that type of device. (See page 37 for more
x DTS Digital Mode Selector: When alevels. Press and hold the button for three
DTS-encoded digital source is selected, eachinformation on using the remote with productsseconds and then release it. Note that the
other than the AVR 320.)
press of this button will scroll thorugh the avail-test tone will begin circulating, and the
able DTS modes. The specific choice of modesProgram/SPL Indicator c will change
will vary according to whether or not the source33Preset Up/Down:When the tuner is colors. During this sequence, EzSet will
material contains DTS-ES 6.1 Discrete encoding.in use, press these buttons to scroll through the automatically adjust the output levels for all
stations programmed into the AVR 320Os mem-
When a DTS source is not in use, this button haschannels until they are equal, as shown by
no function. (See page 40 for the available DTSory. When some source devices, such as CDthe Program/SPL Indicator c lighting
Digital options.)players, VCRs and cassette decks, are selectedgreen for each channel. Press this button
using the device Input Selectors e, theseagain when the adjustment is complete to
y Logic 7 Selector: Press this button tobuttons may function as Chapter Step or Trackturn off the test tone. (See page 24 for more
select from among the available Logic 7 sur-Advance.information on EzSet.)
round modes. (See page 26 for the available
Logic 7 options.)34Clear Button:Press this button to clear42Learn Button:Press this button to begin
incorrect entries when using the remote to the process of Olearning� the codes from another
z Skip Down Button: This button does notdirectly enter a radio stationOs frequency.productOs remote into the AVR 320Os remote. (See
have a direct function on the AVR 320, butpage 37 for more information on using the
when used with a compatibly programmed CD35Memory Button:Press this button toremoteOs learning function.)
or DVD changer it will change to the previous
enter a radio station into the AVR 320Os preset
disc in the changer or carousel.memory. Once the MEMORY Indicator U43Mute:Press this button to momentarily
` Transport Controls: These buttons doflashes, you have five seconds to enter a presetsilence the AVR 320 or TV set being controlled,
memory location using the Numeric Keysdepending on which device has been selected.
not have any functions for the AVR 320, butr. (See page 31 for more information.)When the AVR 320 remote is being programmed
they may be programmed for the forward/
to operate another device, this button is pressed
reverse play operation of a wide variety of CD36Delay/Prev Ch.:Press this button towith the Input Selector Button e to begin
or DVD players, and audio or video cassette
begin the process for setting the delay timesthe programming process. (See page 37 for
recorders. (See page 40 for more information.)used by the AVR 320 when processing surroundmore information on programming the remote.)
28Skip Up Button:This button does notsound. After pressing this button, the delay
times are entered by pressing the Set Button44EzSetSensor Microphone:The sensor
have a direct function on the AVR 320, but
when used with a compatibly programmed CDp and then using the ?/¤ Buttons n tomicrophone for the EzSet microphone is behind
change the setting. Press the Set Button pthese slots. When using the remote to calibrate
or DVD changer it will change to the previousagain to complete the process. (See page 23 forspeaker output levels using EzSet, be sure that
disc in the changer or carousel.
more information.)you do not hold the remote in a way that cov-
ers these slots. (See page 24 for more informa-
29Stereo Mode Select Button:Pressing
37?Button:Press this button to change ation on using EzSet.)
this button cycles through the stereo modes,setting or selection when configuring many of the
and it is also used to turn off all surround
AVR 320Os settings.
14 MAIN REMOTE CONTROL FUNCTIONS |